BlackBerry Phones Update/Flash Easy Way;)





BlackBerry Phones Update/Flash Easy Way Without BlackBerry Desktop Manager


1: Download ; install the blackberry flashfile (no need install blackberry desktop manager)

2: Delete the vendor.xml file located in c:\program files\common files\research in motion\apploader

3: With battery Connect your BlackBerry device to your computer

4: Run Loader from c:\program files\common files\research in motion\apploader & click Next

5: Select all software you want installed.

6: Proceed to the end portion untill you see the "Finish" button

7: Very IMPORTANT. do not hit the finish button, instead select the ADVANCED button.

8: Make sure both boxes are checked.

9: Proceed until it ask you if you want to automatically back up and restore, Select DO NOT AUTOMATICALLY BACK UP MY HANDHELD do next

10: and; wait for Your device's software has been updated successfully

iPhone 3G / 3GS Glass Digitizer Replacement Repair

iPhone 3GS Battery Replacement Directions

iPhone 3GS Take Apart & Repair Directions

iPhone 3G Touchscreen Repair Videos

 PART 1



PART 2

iPhone 3G Disassemby / LCD replacement

iPhone 3G LCD / Display Replacement Guide

Steps

first image

Add Note Step 1 — Display

  • Remove the two Phillips #00 screws from the dock-connector end of the iPhone.
first image

Add Note Step 2

  • Remove the metal handle from the suction cup. It's easier and safer to grip the suction cup's base instead of the metal handle.
  • Be very careful when opening the iPhone so that the cables under the display are not severed.
  • There is a rubber gasket between the silver front bezel and black display assembly. A bit of force is required in this step to separate the iPhone's display assembly.
  • Use a small suction cup near the Home button to gently pull up the bottom portion of the iPhone's display assembly.
first image

Add Note Step 3

  • The display assembly is still connected to the iPhone by several cables, so don't try to remove it entirely just yet.
  • Rotate the display assembly up until it is at an angle of approximately 45 degrees.
first image

Add Note Step 4

  • Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1."
first image

Add Note Step 5

  • Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.
  • Use a spudger to disconnect the black ribbon cable labeled "2."
first image

Add Note Step 6

  • Use a spudger to flip up the black plastic tab holding the remaining ribbon cable in place. The black will rotate up 90 degrees, releasing the ribbon cable.
  • The plastic tab may be white (instead of black) on some iPhone models.
  • Slide the ribbon cable out of its connector, and remove the display assembly from the iPhone.
first image

Add Note Step 7

  • Remove the single Phillips #00 screw from the corner of the display assembly.
first image

Add Note Step 8

  • Remove the two Phillips #00 screws from the right side of the display assembly.
first image

Add Note Step 9

  • Turn the display over, and carefully peel up the thin strip of black tape on the edge of the display assembly.
  • Keeping the tape from sticking to itself can be tricky. We recommend placing the tape on a wax-coated piece of paper (any sticker backing will do).
first image

Add Note Step 10

  • Remove the three Phillips #00 screws from the left side of the display assembly.
first image

Add Note Step 11

  • Carefully insert a metal spudger between the two metal rails along the edge of the display assembly. Gently rotate the spudger to lift the LCD up from the glass.
first image

Add Note Step 12

  • Turn the display assembly over and again carefully insert a metal spudger between the two metal rails along the edge of the display assembly. Gently rotate the spudger to lift the LCD up from the glass.
first image

Add Note Step 13

  • Separate the LCD and glass by sliding the LCD panel away from the ribbon cables on the glass.

Congratulations!

Installing iPhone 3G Battery

 PDF Guide

 

Steps

first image

Add Note Step 1 — Battery


  • Remove the two Phillips #00 screws from the dock-connector end of the iPhone.

first image

Add Note Step 2


  • There is a rubber gasket between the silver front bezel and black display assembly. A bit of force is required in this step to separate the iPhone's display assembly.


  • Use a small suction cup near the Home button to gently pull up the bottom portion of the iPhone's display assembly.

first image

Add Note Step 3


  • The display assembly is still connected to the iPhone by several cables, so don't try to remove it entirely just yet.


  • Rotate the display assembly up until it is at an angle of approximately 45 degrees.

first image

Add Note Step 4


  • Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1."

first image

Add Note Step 5


  • Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.


  • Use a spudger to disconnect the black ribbon cable labeled "2."

first image

Add Note Step 6


  • Some iPhone 3Gs may have the connector colors reversed (black plastic tab, white connector). Make sure you're flipping up the tab properly, otherwise you may damage the connector.


  • Use a spudger to flip up the white plastic tab holding the remaining ribbon cable in place. The white tab will rotate up 90 degrees, releasing the ribbon cable.


  • Slide the black ribbon cable out of its connector, and remove the display assembly from the iPhone.

first image

Add Note Step 7


  • Insert your SIM eject tool or a paper clip into the hole next to the headphone jack.


  • Press down on the tool until the SIM card tray pops out.


  • Grasp the SIM card tray and slide it out of the iPhone.

first image

Add Note Step 8


  • Use a spudger to disconnect the ribbon cable labeled "4."

first image

Add Note Step 9


  • Use a spudger to disconnect the ribbon cable labeled "5."

first image
thumb image 1
thumb image 2

Add Note Step 10


  • Use a spudger to disconnect the ribbon cable labeled "6."


  • If you have an iPhone 3GS, refer to picture 2 and use a spudger to disconnect the ribbon cable labeled "7."

first image

Add Note Step 11


  • Carefully peel up the small sticker labeled "Do not remove."

first image

Add Note Step 12


  • Remove the following 8 screws:


    • Five 2.3 mm Phillips #00 screws with partial threads securing the logic board to the rear panel.


    • Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera.


    • One 2.9 mm Phillips #00 screw from beneath the "Do not remove" sticker.

first image

Add Note Step 13


  • Use a spudger to gently pry the camera up and out of its housing in the rear panel. The camera cannot be removed entirely yet because it's connected to the bottom of the logic board.

first image

Add Note Step 14


  • Use a spudger to gently pry up the end of the logic board closest to the dock connector.


  • If the board won't lift up, double check to make sure all the screws securing the logic board have been removed.

first image

Add Note Step 15


  • Slide the logic board towards the dock connector and out of the iPhone.

first image

Add Note Step 16


  • Use a spudger to pry the battery up from the rear panel. The battery is attached with an adhesive strip around the perimeter of the battery. To prevent the battery from bending during the removal process, we recommend against using just the plastic pull-tab .